Monothane HS 50 Gloss
Single pack moisture cure polyurethane sets the industry standard of 50% solids, providing extremely good flow and leveling properties.
- May be used for interior coating of ALL timber species, cork, particle board and concrete.
- Can be applied over TIMBERSEAL OR DUOTHANE FAST A/ DUOTHANE PART A and DUOTHANE PART B.
- Compatible with MONOTHANE 45 GLOSS, MONOTHANE 44 GLOSS & MONOTHANE LOW SHEENS.
Fine sand to a smooth finish (Not finer than #120 mesh). Hardwoods must not be burnished and grain must remain open. Vacuum thoroughly. Ensure the timber surface if free from dust, wax or oily substances.
Clean with hot water and detergent. Roughen surface completely with 150 mesh screenback and vacuum thoroughly. Wipe floor with URETHANE COATINGS THINNERS. Test for compatibility by applying MONOTHANE HS 50 GLOSS on a small section of floor first. If 'craters' or 'fisheyes' appear, add 10mls of FLOWMAX Anti Rejection Fluid per litre of MONOTHANE HS 50 GLOSS and refer to FLOWMAX directions.
NB : Do not use MONOTHANE HS 50 GLOSS at temperatures below 10°C or above 30°C. On cold days, during the final floor preparation, wrap the drum in an electric blanket set on ‘1’ (low heat) or place the drum in a tub of hot water and operate building heating, (Air conditioning or portable oil filled radiator type heaters are ideal. Any type of heating with a naked flame or with very hot surfaces are not recommended). Turn heating off prior to application of coatings.
- Apply with a mohair roller, lamb’s wool applicator or brush, allow 4-6 hours to dry. Do not return unused material to the can. New cork and timber floors will need 3 and 2 coats respectively, sand with 150 mesh screenback between coats.
- Thoroughly clean the mohair roller, lamb’s wool applicator or brush in URETHANE COATINGS CLEANING SOLVENT. Dry all equipment before using.
- URETHANE COATINGS CATALYST may be added to the first coat of MONOTHANE to accelerate curing.
10m² per litre. URETHANE COATINGS THINNERS may be added if MONOTHANE has thickened, or if a higher coverage and a thinner coat is required.
MONOTHANE requires 7-10 days to fully cure by absorbing moisture from the atmosphere. Avoid heavy traffic during this period. Use protective pads under legs of furniture.
Regularly wipe over the floor with an antistatic mop or sweep with a soft bristle broom. We caution against the use of vacuum cleaners, particularly if the bristles are worn as the cleaning head may then scratch the floor. The frequency of cleaning is dependent on the level of traffic, amount of grit carried onto the floor, and activity of children, and pets etc.
To clean your floor, mix up to one cup of Methylated Spirits into a bucket of hot water, and mop the floor, regularly rinsing the mop. If the floor is particularly dirty, wash first with a non abrasive detergent then clean with the Methylated spirits and water solution – this will prevent streaking and smear marks that sometimes remain after use of detergents and/or household cleaners.
This product is best if used within 12 months from manufacture (refer to batch number), when stored in unopened containers under normal conditions of temperature and humidity.
Contains no more than 0.7 grams per 100mls of volatile free organic isocyanate.
Usage of this material must be under well ventilated conditions to minimise inhalation of vapours. Wear respirator with filters that conform with AS1716. Asthmatics, the very young, elderly people and pets should leave the site during the first 24 hours. Prevent skin contact by wearing impervious gloves. Breathing of vapour is harmful and may cause lung irritation and allergic respiratory reaction. May irritate skin and eyes. Keep container firmly lidded, as this product cures when exposed to air. In case of spillage, absorb into dry sand or dirt. Remove from work area and cover with water for 24 hours prior to disposal.
Contains 325gms per litre of Aromatic Hydrocarbons. This drum contains volatile and flammable solvents and when applying the contents adequate ventilation to the outside must be provided. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep drum closed when not in use.
If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or milk.
CONTACT DOCTOR OR POISONS INFORMATION CENTRE Australia 131126.
In case of eye contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove contaminated clothing and wash skin first with Methylated spirits, then with soap and water.